Can I Set Up A Tub Myself?
Can I Set Up A Tub Myself?
Blog Article
They are making a few great observations regarding How to Install a Bathtub: Install an Acrylic Tub and Tub Surround as a whole in the article just below.
Setting up a bathtub isn't exactly brain surgery, however it does call for strong plumbing, carpentry, and occasionally, tiling abilities. Replacing an old bath tub with a brand-new one is also a reasonably tough job. If the old tub is conveniently available, the task can move quickly; if you need to open a wall to get rid of the old tub and also position the brand-new tub, the task is a lot harder. In either case, the task is within a house handyman's skills, although you will certainly need an assistant to move out the old bathtub as well as embeded in the new one. Make sure you have actually qualified on your own for the job and also are comfortable trying it. Instead of working with a specialist to take control of a halfway-completed job, it is far better to think about employing one prior to you begin. Possibilities are you might need a specialist plumber to make tube connections.
This post will certainly assist you mount a new bath tub in your restroom if you have actually already gotten a brand-new tub as well as do not need to alter the setup of your previous water supply pipelines.
Your devices as well as product list must consist of the following:
Planning for the Installment
Firstly, the supporting frame supplied with the bath ought to be fitted (if needed) according to the maker's directions. Next, fit the taps or mixer to the tub. When fitting the tap block, it is very important to ensure that if the faucet comes with a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bath, it is likewise reasonable to fit a supporting plate under the faucets device to prevent pressure on the bathtub.
Fit the versatile tap adapters to the bottom of the two taps making use of 2 nuts and olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet via the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. See to it you make use of every one of the provided washing machines.
Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bath should now prepare to be suited its last placement.
Removing Old Touches
If you need to replace old taps with new ones as a part of your installation, then the first thing you should do is disconnect the water supply. After doing so, turn on the taps to drain pipes any kind of water continuing to be in the system. The procedure of eliminating the existing faucets can be rather troublesome because of the restricted access that is frequently the case.
Make use of a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the taps. Have a cloth all set for the staying water that will certainly originate from the pipes. As soon as the supply pipes have actually been eliminated, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary taps from transforming during this procedure. Once the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any old securing compound.
Prior to moving on to fit the brand-new taps, contrast the pipe links on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Setting up the Bathtub
Utilizing the two wood boards under its feet, position the tub in the called for setting. The wood boards are useful in uniformly spreading out the weight of the tub over the location of the boards instead of concentrating all the weight onto four little factors.
The next objective is to ensure that the tub is leveled all round. This can be attained by inspecting the level and changing the feet on the bath tub until the level reviews level.
To set up faucets, fit the bottom of the outermost adaptable tap port to the ideal supply pipe by making a compression sign up with; after that do the same for the other tap.
Turn on the water and inspect all joints and also new pipework for leaks as well as tighten them if essential. Fill the tub as well as additionally check the overflow outlet and also the regular outlet for leaks.
Finally, repair the bathroom paneling as defined in the manufacturer's instruction manual. Tiling as well as securing around the bath tub should wait up until the tub has actually been made use of at least once as this will resolve it right into its final setting.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will need a plastic port to stop damage to the thread. One end of the port fits on the plastic tail of the faucet and the various other end provides a connection to the current supply pipes.
If you need to fit a monobloc, after that you will need minimizing couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, place the faucet in the mounting hole in the bath/basin making sure that the washing machines are in place in between the faucet and the sink. Protect the faucet in position with the manufacturer offered backnut. When the faucet is firmly in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with typical faucet adapters. The previous kind needs to be attached to the faucet finishes initially, tightening up only by hand. The supply pipes can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Tub
In the area where the bath fulfills the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is essential as the fitting can move enough to fracture an inflexible seal, triggering the water to permeate the wall between the bathroom and also the tiling, causing issues with dampness and feasible leakages to the ceiling below.
You can choose from a variety of coloured sealers to assimilate your fixtures and installations. They are offered in tubes as well as cartridges, and can securing spaces up to a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can load it with twists of soaked paper or soft rope. Remember to constantly load the tub with water before sealing, to permit the activity experienced when the bathtub is in use. The sealer can split relatively early if you do not take into account this activity prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also conveniently offered on the market. It is advisable to fit the floor tiles utilizing water-resistant or waterproof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were shown that report on A Step-by-Step Guide to Installing a Bathtub from a friend on a different domain. Liked our write-up? Please share it. Help another person find it. Bless you for your time. Don't forget to pay a visit to our website back soon.
Get Quote Now
Report this page